current:beta
Differences
This shows you the differences between two versions of the page.
Both sides previous revisionPrevious revisionNext revision | Previous revisionNext revisionBoth sides next revision | ||
current:beta [2021/03/18 18:26] – 9.4.39 beta 1 James Sentman | current:beta [2021/12/25 15:44] – James Sentman | ||
---|---|---|---|
Line 1: | Line 1: | ||
=====Beta Versions===== | =====Beta Versions===== | ||
- | Beta 1 of version 9.4.39 is available as of 3/18/2021. | ||
- | This version | + | ====XTension Beta 9.4.45 for ARM and X86==== |
+ | Released: 12/ | ||
+ | \\ | ||
+ | There is now a native ARM64 build for Apple’s M1 chip devices. The X86 version continues | ||
- | Since the build number has been incremented a backup of your database | + | In general |
- | Download: [[https:// | + | Both M1 and original X86 compiles |
+ | In addition to the M1 build this beta includes the following changes and fixes: | ||
+ | * The Manage Global Scripts window now displays the total number of scripts with errors in it’s title as well as the number of scripts with errors in each folder throughout the list. The number of scripts in each folder is also displayed. | ||
+ | * Plugins that are running remotely no longer send pings when the interface is disconnected so errors about them are no longer incorrectly logged. | ||
+ | * Fixed a potential problem in the XTension kit receiver plugin if a device sent invalid JSON characters. It no longer causes the listening thread to stop completely but rather logs an appropriate error and continues to function for every other device. | ||
+ | * Added support to the XTension kit plugin for new and upcoming devices. | ||
+ | * For the M1 build an error is no longer created at startup due to Apple no longer supporting some of the default icons that I was pulling from the system. | ||
+ | * The Genmon plugin will update the label of the Engine State unit even if the state of the engine has not changed. | ||
+ | * Genmon: Added many new error and status units so that it is simpler to get specific information than to parse the label of the engine status unit. New units created include: | ||
+ | * Error: Engine Speed High or Low | ||
+ | * Error: Governor failure | ||
+ | * Error: Low Oil | ||
+ | * Error: Overcrank | ||
+ | * Error: Overheat | ||
+ | * Error: Overload | ||
+ | * Error: RPM Sensor | ||
+ | * Error: Voltage High or Low | ||
+ | * Error: Warning (generator is sending a warning that is not yet an error or alarm condition) | ||
+ | * Generator Is In Alarm | ||
+ | * Generator Is Running | ||
+ | * Generator Is Ready | ||
+ | * Generator Is Exercising | ||
+ | * Generator Is Ready | ||
+ | * Generator Service Is Due | ||
- | Change Log: | + | Note that the M1 version is not a Universal build and will not run on X86 based machines. While the X86 version runs just fine on the M1 chip under emulation |
- | * Hubitat: new “pin code unit” device type added to support knowing which pin code was used to unlock | + | |
- | * Hubitat: The Lock unit will let you lock and unlock the door remotely by selecting that state from the popup or using the enumerated commands something like: set value of “your lock unit” to “locked” | + | Download for M1: [[https:// |
+ | Download for X86: [[https:// | ||
- | Known Issues: | ||
- | As of this moment lock units when created may show unlocked as the state even if the door is locked when the unit is first created. After the first change of state either remotely or via the lock itself the unit will then be in sync. |
current/beta.txt · Last modified: 2024/02/05 17:51 by James Sentman