Vera Plus and Barix

[James Sentman]

Hello Henk,

Can you put  the Vera interface into debug mode and then run the series of commands that are causing the error? Send me the log output off the list.

I assume that the combination of barix errors and vera errors are just because you’re commanding the same units at the same time and not actually related. If you command that Vera unit without also commanding the Barix units do you get the same error? 

As far as enabling the Barix interface there I can’t tell if you’re using the new barix interface or the older original one. It’s possible that you just have some barix units assigned to the interface with addresses that either aren’t supported on that Barix or are leftover from a previous install or something and it’s trying to init them and the barix is just telling us that those addresses cannot exist. I can’t think of any way that the barix and vera errors could be directly connected.


> On Mar 20, 2020, at 2:59 PM, Hendrik W. M. van Eeden <hvaneeden at comcast.net> wrote:
> 
> I have been getting these errors lately:
> 
> 3/20/20 2:10:44 PM  Turning Rotators OFF
> 3/20/20 2:10:44 PM  SECURITY SYSTEM ARMED AWAY
> 3/20/20 2:10:44 PM Xmas Front Door Ligh: Sending the Z-Wave command after 0 retries (Vera Plus)
> 3/20/20 2:10:44 PM Received OFF for VestibuleOFF relay 2 (Barionet)
> 3/20/20 2:10:44 PM Received ON for VestibuleOFF relay 2 (Barionet)
> 3/20/20 2:10:44 PM Sending OFF for "VestibuleOFF relay 2" (Barionet)
> 3/20/20 2:10:44 PM Received ON for HallOFF relay 4 (Barionet)
> 3/20/20 2:10:44 PM Received OFF for VestibuleOFF relay 2 (Barionet)
> 3/20/20 2:10:44 PM Vera Plus: unexpected result from off command: "ERROR: Invalid service/action/device" (Vera Plus)
> 3/20/20 2:10:45 PM Vera Plus: unexpected result from off command: "ERROR: Invalid service/action/device" (Vera Plus)
> 3/20/20 2:10:45 PM Xmas Front Door Ligh: Waiting to send again with ack (Vera Plus)
> 3/20/20 2:10:45 PM LED Lights: Waiting to send again with ack (Vera Plus)
> 3/20/20 2:10:45 PM Watering Tree: (Vera Plus)
> 3/20/20 2:10:45 PM Xmas  Mantle light: Waiting to send again with ack (Vera Plus)
> 3/20/20 2:10:45 PM Xmas House: Waiting to send again with ack (Vera Plus)
> 3/20/20 2:10:45 PM Xmas Lights side doo: Waiting to send again with ack (Vera Plus)
> 3/20/20 2:10:45 PM Temp tree lights: Waiting to send again with ack (Vera Plus)
> 3/20/20 2:10:45 PM Xmas Mantle LR: Sending the Z-Wave command after 0 retries (Vera Plus)
> 3/20/20 2:10:45 PM Vera Plus: unexpected result from off command: "ERROR: Invalid service/action/device" (Vera Plus)
> 3/20/20 2:10:45 PM Xmas Front Door Ligh: (Vera Plus)
> 
> Then I get these errors when enabling the Barix interface.
> 
> 3/20/20 2:51:53 PM Barionet: begin connected (Barionet)
> 3/20/20 2:51:53 PM Barionet: Barionet: Barix Plugin v2.2 found a BARIONET 1.3 (Barionet)
> 3/20/20 2:51:53 PM Barionet: Received barix command error (cmderr) (Barionet)
> 3/20/20 2:51:53 PM Barionet: Received barix command error (cmderr) (Barionet)
> 3/20/20 2:51:53 PM Barionet: Received barix command error (cmderr) (Barionet)
> 3/20/20 2:51:53 PM Barionet: Received barix command error (cmderr) (Barionet)
> 3/20/20 2:51:53 PM Barionet: Received barix command error (cmderr) (Barionet)
> 3/20/20 2:51:53 PM Barionet: Received barix command error (cmderr) (Barionet)

Thanks,
 James


James Sentman                       http://www.PlanetaryGear.org		http://MacHomeAutomation.com




-------------- next part --------------
An HTML attachment was scrubbed...
URL: <http://mail.machomeautomation.com/pipermail/xtensionlist/attachments/20200320/336b16d0/attachment.html>